Share
Pin
Tweet
Send
Share
Send
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi.jpg)
At this stage, we will need wire and red beads, and for now we are laying aside white. So, cut off 15 cm of red wire and put on it 5 red beads. Move them to the middle and twist, as shown in the picture.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-2.jpg)
Now again we put 5 beads on one of the ends of the wire and twist.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-3.jpg)
We put on 5 beads again, only now on the other end of the wire and twist.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-4.jpg)
We repeat all this until on our branch there will be 4 petals on each side. We will need 15 of these.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-5.jpg)
Working according to the same scheme, we make 32 more things, only they should not have 4 petals, but 3 each.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-6.jpg)
For one branch, we need 3 large branches and 6 small ones.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-7.jpg)
Now we take white beads and a white wire. We should get 32 small branches and 15 large ones. In the end, it will be so much:
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-8.jpg)
It's time to engage in the formation of the main 5 branches. Here is what we will need:
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-9.jpg)
In order for our twig to turn out plump, cut about 50 pieces of a 10-centimeter wire. Take a wire of 0.4 ml thick. We proceed to the formation of the twig. Take a twig with 4 petals each and wind a piece of wire to it with mouline thread.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-10.jpg)
Now we take a branch with 3 petals each and wind it to the main branch. We attach a piece of wire and attach it. The distance should be small, approximately as in the picture.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-11.jpg)
Do not forget to thicken the main branch with pieces of wire after every 2 branches. Add branches with 3 petals each. On each side should get 4 branches of 3 petals. The last fifth branch is taken from 4 petals. Here is such a large branch you should get.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-12.jpg)
But we will have one big branch, the remaining 4 branches we will do without 1 branch (on each side) of three petals. But the last branch must necessarily be of 4 petals. We will get 5 branches, in the center the largest branch. We repeat everything with white branches.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-13.jpg)
We take the largest branch and wind the branch to it
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-14.jpg)
We attach each twig at a distance of 3-4 centimeters. We do the same with white branches. It will turn out like this.
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-15.jpg)
Straighten the branches and fasten them with wire. But I did a little in my own way. She took the plaster and coated it with branches. I also made a stand for our tree from plaster. I painted the finished composition with simple colors and decorated it with flowers, which I also made of beads.
That's the beauty I got !!!
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-16.jpg)
![](http://img.uaft2404.org/img/sdela-2019/derevo-lyubvi-17.jpg)
Share
Pin
Tweet
Send
Share
Send